wiped u-boot enviroment

[xhpohanka]

Hi Codesnake,
thank you for your work on OpenELEC.

I have unbranded g18 board (same as Matricom MX2) and I got it with erased nand flash. I have build openelec from source and flashed it using sd card recovery. Unfortunately I see on serial line that there is some problem with booting. It seems to me, that u-boot does not know partition names (logo, boot, etc.) - mtdparts variable is not defined. Is it normal?

I'm able to boot openelec manually by loading kernel from sd card and running bootm command.
Can you please share what u-boot enviroment variables has to be set?

regards
Jan

[codesnake]

NAND partition table is not stored in u-boot environment variables. It is defined in kernel device tree.

[codesnake]

At each boot kernel reads NAND partition layout from device tree and updates it in NAND environment area. During firmware install first time this is performed by recovery's kernel. Then u-boot reads parition layout from NAND environment area and boots from boot partition.

[xhpohanka]

Then I do not understand why my device does not boot with clean install. Maybe there are some bad blocks around env area.

I'm getting big number of similar warnings during kernel booting

[    4.942949@0] ########aml_nand_read_oob 3583 read oob failed here at at page:23040, blk:90 chip[0]
[    4.946311@0] aml_ops_read_page failed: 8400000 66 0
[    4.951230@0] unkown page 0 spare data 22,22,22,22
[    4.956035@0] block: 66 page: 1 occured unusual
[    4.962899@0] ########aml_nand_read_oob 3583 read oob failed here at at page:23041, blk:90 chip[0]
[    4.969476@0] aml_ops_read_page failed: 8402000 66 1
[    4.974437@0] unkown page 0 spare data 22,22,22,22
[    4.979181@0] block: 66 page: 2 occured unusual
[    4.985685@0] ########aml_nand_read_oob 3583 read oob failed here at at page:23042, blk:90 chip[0]
[    4.992684@0] aml_ops_read_page failed: 8404000 66 2
[    4.997582@0] unkown page 0 spare data 22,22,22,22
[    5.002378@0] block: 66 page: 3 occured unusual
[    5.008836@0] ########aml_nand_read_oob 3583 read oob failed here at at page:23043, blk:90 chip[0]
[    5.015856@0] aml_ops_read_page failed: 8406000 66 3
[    5.020756@0] unkown page 0 spare data 22,22,22,22
[    5.025552@0] block: 66 page: 4 occured unusual
[    5.032553@0] ########aml_nand_read_oob 3583 read oob failed here at at page:23044, blk:90 chip[0]
[    5.039002@0] aml_ops_read_page failed: 8408000 66 4
[    5.043955@0] unkown page 0 spare data 22,22,22,22
[    5.048708@0] block: 66 page: 5 occured unusual
[    5.055646@0] ########aml_nand_read_oob 3583 read oob failed here at at page:23045, blk:90 chip[0]
[    5.062212@0] aml_ops_read_page failed: 840a000 66 5
[    5.067106@0] unkown page 0 spare data 22,22,22,22
[    5.071879@0] block: 66 page: 6 occured unusual
[    5.079121@0] ########aml_nand_read_oob 3583 read oob failed here at at page:23046, blk:90 chip[0]
[    5.085377@0] aml_ops_read_page failed: 840c000 66 6
[    5.090282@0] unkown page 0 spare data 22,22,22,22
[    5.095086@0] block: 66 page: 7 occured unusual
[    5.102141@0] ########aml_nand_read_oob 3583 read oob failed here at at page:23047, blk:90 chip[0]
[    5.108529@0] aml_ops_read_page failed: 840e000 66 7
[    5.113486@0] unkown page 0 spare data 22,22,22,22
[    5.118231@0] block: 66 page: 8 occured unusual

And this is what u-boot says

aml_rtc_init
aml rtc init first time!
clr h-ram
DRAM:  1 GiB
relocation Offset is: 105e0000
MMC:   [mmc_register] add mmc dev_num=0, port=1, if_type=6
[mmc_register] add mmc dev_num=1, port=2, if_type=6
SDIO Port B: 0, SDIO Port C: 1
NAND:  Amlogic nand flash uboot driver, Version U1.06.020 (c) 2010 Amlogic Inc.
NAND BOOT : nand_init 1133 
No NAND device found!!!
NAND device id: 2c 64 44 4b a9 0 
NAND device: Manufacturer ID: 0x2c, Chip ID: 0x2c (Micron B revision NAND 8GiB MT29F64G08CBABA)
#####aml_nand_init, with RB pins and chip->chip_delay:20
bus_cycle=5, bus_timing=6, start_cycle=6, end_cycle=7,system=5.0ns
m3:###aml_chip->boot_oob_fill_cnt =-1524
oob size is not enough for selected bch mode: NAND_BCH60_1K_MODE force bch to mode: NAND_BCH40_1K_MODE
aml_chip->oob_fill_cnt =168,aml_chip->oob_size =744,bch_bytes =70
Creating 1 MTD partitions on "nandboot":
0x000000000000-0x000000800000 : "nandboot"
nandboot initialized ok
detect mx chiprevD :1 and nand_type: 40
NAND BOOT : nand_init 1133 
No NAND device found!!!
NAND device id: 2c 64 44 4b a9 0 
NAND device: Manufacturer ID: 0x2c, Chip ID: 0x2c (Micron B revision NAND 8GiB MT29F64G08CBABA)
1 NAND chips detected
#####aml_nand_init, with RB pins and chip->chip_delay:20
bus_cycle=5, bus_timing=6, start_cycle=6, end_cycle=7,system=5.0ns
oob size is not enough for selected bch mode: NAND_BCH60_1K_MODE force bch to mode: NAND_BCH40_1K_MODE
aml_chip->oob_fill_cnt =168,aml_chip->oob_size =744,bch_bytes =70
multi plane error for selected plane mode: NAND_TWO_PLANE_MODE force plane to : NAND_SINGLE_PLANE_MODE
aml_nand_init:oobmul =1,chip->ecc.layout->oobfree[0].length=16,aml_chip->oob_size=744
########aml_nand_read_page_hwecc 3474 read ecc failed here at at page:1280, blk:5 chip[0]
aml_nand_env_init:6035,offset =a00000
########aml_nand_read_page_hwecc 3474 read ecc failed here at at page:1536, blk:6 chip[0]
aml_nand_env_init:6035,offset =c00000
########aml_nand_read_page_hwecc 3474 read ecc failed here at at page:1792, blk:7 chip[0]
aml_nand_env_init:6035,offset =e00000
aml nand env valid addr: 820000 ,status =0
key start_blk=4088,end_blk=4095,aml_nand_key_init:684
########aml_nand_read_page_hwecc 3474 read ecc failed here at at page:1046528, blk:4088 chip[0]
blk check good but read failed: 1ff000000, -74
########aml_nand_read_page_hwecc 3474 read ecc failed here at at page:1046784, blk:4089 chip[0]
blk check good but read failed: 1ff200000, -74
########aml_nand_read_page_hwecc 3474 read ecc failed here at at page:1047046, blk:4090 chip[0]
blk check good but read failed: 1ff40c000, -74
aml nand key valid addr: 1ff400000 
aml nand key valid addr: 1ff600000 
aml nand key valid addr: 1ff800000 
CONFIG_KEYSIZE=0x10000; KEYSIZE=0xfffc; bbt=0x1330; default_keyironment_size=0xeccc
i=0,register --- nand_key
Creating 5 MTD partitions on "nandnormal":
0x000001000000-0x000001800000 : "mtd1"
0x000001800000-0x000002000000 : "mtd2"
0x000002000000-0x000002800000 : "mtd3"
0x000002800000-0x000003000000 : "mtd4"
0x000003000000-0x00000a000000 : "mtd5"
nandnormal initialized ok
detect mx chiprevD :1 and nand_type: 40
nand_curr_device =1
NAND BOOT,nand_env_relocate_spec : env_relocate_spec 49 
In:    serial
Out:   serial
Err:   serial
register usb cfg[0][1] = 9fe85ad0
Net:   Meson_Ethernet
init suspend firmware done. (ret:0)
detect_storage
nand exist return 0
setenv storage nand
reboot_mode=charging
wipe_data=success
ir init
Hit Enter key to stop autoboot -- :  1 tstc enter